Bitte stellen Sie zuerst sicher, dass Sie die neueste SIP Firmware auf Ihr Telefon aufspielen. Kontaktieren Sie bitte Ihren Cisco Partner für weitere Informationen.

Die für ein Cisco IP Phone benötigten Dateien SIP<MAC-Adresse> und SIPDefault.cnf sollten wie folgt aussehen:

SIPDefault.cnf

# Image Version
image_version: "P0S3-07-1-00"

# Emergency Proxy info
proxy_emergency: ""
proxy_emergency_port: "5060"

# Backup Proxy info
proxy_backup: ""
proxy_backup_port: "5060"

# Outbound Proxy info
outbound_proxy: ""
outbound_proxy_port: ""

# NAT/Firewall Traversal
nat_enable: "1"
nat_address: ""
voip_control_port: "5060"
start_media_port: "16000"
end_media_port: "16100"
nat_received_processing: "1"

# Proxy Registration (0-disable (default), 1-enable)
proxy_register: "1"

# Phone Registration Expiration [1-3932100 sec] (Default - 3600)
timer_register_expires: "3600"

# Codec for media stream (g711ulaw (default), g711alaw, g729a)
preferred_codec: "g729a"

# TOS bits in media stream [0-5] (Default - 5)
tos_media: "5"

# Enable VAD (0-disable (default), 1-enable)
enable_vad: "0"

# Allow for the bridge on a 3way call to join remaining parties upon hangup
cnf_join_enable: "1" ; 0-Disabled, 1-Enabled (default)

# Allow Transfer to be completed while target phone is still ringing
semi_attended_transfer: "0" ; 0-Disabled, 1-Enabled (default)

# Telnet Level (enable or disable the ability to telnet into this phone
telnet_level: "1" ; 0-Disabled (default), 1-Enabled, 2-Privileged

# Inband DTMF Settings (0-disable, 1-enable (default))
dtmf_inband: "1"

# Out of band DTMF Settings (none-disable, avt-avt enable (default), avt_always - always avt )
dtmf_outofband: "avt"

# DTMF dB Level Settings (1-6dB down, 2-3db down, 3-nominal (default), 4-3db up, 5-6dB up)
dtmf_db_level: "3"

# SIP Timers
timer_t1: "500" ; Default 500 msec
timer_t2: "4000" ; Default 4 sec
sip_retx: "10" ; Default 11
sip_invite_retx: "6" ; Default 7
timer_invite_expires: "180" ; Default 180 sec

# bellSIP Voicemail
messages_uri: "5555"

#********* Release 2 new config parameters **********

# TFTP Phone Specific Configuration File Directory
tftp_cfg_dir: "./"

# Time Server
sntp_mode: "directedbroadcast"
sntp_server: "17.254.0.49"
time_zone: "CET"
dst_offset: "1"
dst_start_month: "April"
dst_start_day: ""
dst_start_day_of_week: "Sun"
dst_start_week_of_month: "1"
dst_start_time: "02"
dst_stop_month: "Oct"
dst_stop_day: ""
dst_stop_day_of_week: "Sunday"
dst_stop_week_of_month: "8"
dst_stop_time: "2"
dst_auto_adjust: "1"

# Do Not Disturb Control (0-off, 1-on, 2-off with no user control, 3-on with no user control)
dnd_control: "0" ; Default 0 (Do Not Disturb feature is off)

# Caller ID Blocking (0-disabled, 1-enabled, 2-disabled no user control, 3-enabled no user control)
callerid_blocking: "0" ; Default 0 (Disable sending all calls as anonymous)

# Anonymous Call Blocking (0-disbaled, 1-enabled, 2-disabled no user control, 3-enabled no user control)
anonymous_call_block: "0" ; Default 0 (Disable blocking of anonymous calls)

# Call Waiting (0-disabled, 1-enabled, 2-disabled with no user control, 3-enabled with no user control)
call_waiting: "1" ; Default 1 (Call Waiting enabled)

# DTMF AVT Payload (Dynamic payload range for AVT tones - 96-127)
dtmf_avt_payload: "101" ; Default 100

# XML file that specifies the dialplan desired
dial_template: "dialplan"

# Network Media Type (auto, full100, full10, half100, half10)
network_media_type: "auto"

#Autocompletion During Dial (0-off, 1-on [default])
autocomplete: "1"

#Time Format (0-12hr, 1-24hr [default])
time_format_24hr: "1"

####### New Parameters added in Release 4.0 #######

# bellSIP Logo
logo_url: "http://www.bellsip.com/images/bellsip.bmp"

# HTTP Proxy Support
http_proxy_addr: "" ; Address of HTTP Proxy server
http_proxy_port: 80 ; Port of HTTP Proxy Server (80-default)

# Dynamic DNS/TFTP Support
dyn_dns_addr_1: "" ; restricted to dotted IP
dyn_dns_addr_2: "" ; restricted to dotted IP
dyn_tftp_addr: "" ; restricted to dotted IP

# The dynamic tftp server should be set to whatever your TFTP server is. This way, it
# keeps the tftp server setting even though you might be using DHCP (default behavior
# is to use the DHCP server as a tftp server, which is rarely correct.)

# Remote Party ID
remote_party_id: 1 ; 0-Disabled (default), 1-Enabled

SIP<MAC-Adresse>.cnf

# SIP Configuration

# Proxy Server
proxy1_address: "bellsip.com"
proxy2_address: ""
proxy3_address: ""

proxy1_port:"5060"
proxy2_port:"5060"
proxy3_port:"5060"

# Line 1 Settings
line1_name: "bellSIP Benutzername" ; Line 1 Extension\User ID
line1_displayname: "Ihr Name" ; Line 1 Display Name
line1_authname: "bellSIP Benutzername" ; Line 1 Registration Authentication
line1_password: "bellSIP Passwort" ; Line 1 Registration Password

# Line 2 Settings
line2_name: "" ; Line 2 Extension\User ID
line2_displayname: "" ; Line 2 Display Name
line2_authname: "" ; Line 2 Registration Authentication
line2_password: "" ; Line 2 Registration Password

# Line 3 Settings
line3_name: "" ; Line 2 Extension\User ID
line3_displayname: "" ; Line 2 Display Name
line3_authname: "" ; Line 2 Registration Authentication
line3_password: "" ; Line 2 Registration Password

# Emergency Proxy info
proxy_emergency: ""
proxy_emergency_port: "5060"

# Backup Proxy info
proxy_backup: ""
proxy_backup_port: "5060"

# Outbound Proxy info
outbound_proxy: ""
outbound_proxy_port: "5060"

# NAT/Firewall Traversal
nat_enable: "1"
nat_address: ""
voip_control_port: "5060"
start_media_port: "16000"
end_media_port: "16100"
nat_received_processing: "1"

# Phone Label (Text desired to be displayed in upper right corner)
phone_label: "bellSIP Telefon" ; Has no effect on SIP messaging

# Time Zone phone will reside in
time_zone: CET

# Telnet Level (enable or disable the ability to telnet into this phone
telnet_level: "2" ; 0-Disabled (default), 1-Enabled, 2-Privileged

# Phone prompt/password for telnet/console session
phone_prompt: "SIP Phone" ; Telnet/Console Prompt
phone_password: "Ein von Ihnen gewähltes Passwort" ; Telnet/Console Password

# Enable_VAD (1-enabled, 0-disabled)
enable_vad: "0"

# Network Media Type (auto, full100, full10, half100, half10)
network_media_type: "auto"
user_info: phone

# SIP Configuration Generic File (stop)